NASA's LOLA maps the moon (photos)

Posted by Piscean on 10:13 PM 0 comments

1. The Lunar Orbiter Laser Altimeter, one of seven scientific instruments onboard the Lunar Reconnaissance Orbiter spacecraft, recently completed a project resulting in a new map of the surface of moon with unprecedented detail.

Developed at NASA's Goddard Space Flight Center and launched in June 2009, the Lunar Orbiter Laser Altimeter (LOLA) uses laser ranging to measure the moon's surface elevation, slope, and roughness in 3D. The primary objective was to produce a global geodetic grid for the moon to which all other observations could be geodetically referenced, NASA said.

Here, the most recent LOLA digital elevation map, which was compiled in late 2009 (right) is compared to the previous moon mapping achieved by the Unified Lunar Control Network in 2005. Notice the vastly improved detail of the moon measurements.

Photo by NASA/GSFC/MIT/SVS Caption by James Martin





2. LOLA was designed to assist in the selection of landing sites on the moon for future robotic and human exploration. Previous knowledge of location, direction, and magnitude of surface slopes, and variations in elevation in the region was inadequate, according to NASA.

This is one of LOLA's detailed high-resolution topographic maps of the moon's southern hemisphere.

Though the previous maps of the moon were accurate to around .5 miles to 5 miles, the newest measurements are giving NASA a look at the moon with much more detail.

The newest maps are accurate to the level of 30 meters (.19 miles) or less spatially and 1 meter vertically.
3. The LOLA instrument is not an imaging device, but a measurement tool. The lens is designed not to maintain a specific image quality, but rather to collect the maximum number of photons with the fewest possible losses, and to minimize the background radiation, which might interrupt precise measurements.

The 14-centimeter receiver, a 500-milimeter clear aperture refractive telescope, focuses the received photons on to a fiber optic bundle, according to NASA.

4. To determine an accurate full surface slope of the moon requires the measurement of slope in two directions.

LOLA's multibeam 50-point pattern projected onto the lunar surface provides five measurements in an X-pattern from which the slopes can be derived.

This X-shaped five-point pattern also has the advantage that when rotated, it will provide five near-equidistant parallel profiles, in LOLA's case with approximately 12 meters between each profile.
5. Altimetric ranging systems and the ability to determine the position of the LRO spacecraft lead to significantly greater accuracy than that achieved on earlier missions.

This LOLA topographic map, centered on the Apollo 15 landing site, highlights the Apennine and Caucasus ranges and the fairly subtle wrinkling in Serenitatis. The false colors indicate elevation: red areas are highest and blue lowest.


6. Environmental tests done on the unit included operational and survival thermal testing, assessing temperature extremes, operation in vacuum, and vibration testing.

Here, LOLA is seen integrated into the LRO spacecraft following final testing.

The engineering model optical assemblies are tested with the same optical components as the actual flight model, but they're built with aluminum instead of titanium or beryllium for the structural components, according to NASA.

Testing assemblies while early in development is critical to correct any design flaws, verify all interfaces and optical test procedures, and identify the required optical ground support equipment, the agency said.

If they're not caught before LOLA heads into space, simple miscalculations can doom an entire project.

7. During the one-year mapping period, the measurement laser was fired from the LRO more than 600,000 times, taking more than 3 billion measurements of the moon's surface.

The short pulses from a single laser burst produced a five-beam pattern that achieved the accurate measurements.

With each of the five beams, LOLA measures the time of flight, pulse spreading (which measures the surface roughness), and the transmit versus return of energy (denoting the reflective qualities of the location).

Here, we see the representation of LOLA's data collected from the moon's northern hemisphere. The false colors indicate elevation: red areas are highest and blue lowest.

8. The engineering model transmitter inside the lab undergoing thermal vacuum testing.


9. Inside the lab, engineers prepare to perform an analysis test on LOLA.

Launched on June 18, 2009, the Lunar Reconnaissance Orbiter, carrying LOLA, is the first mission to the moon in more than 10 years.

As the inaugural spacecraft of the United States' "Vision for Space Exploration," the LRO will collect information that will be used in the next generation of NASA's space discoveries.

Leave a Reply